FAMECA voltage detector with integrated self-test. Compact optical and acoustic detector with LEDs.
Rated voltage: 127V to 90 000V.
Frequency: 50 and 60Hz.
Length: 195mm, Diameter: 49mm
Weight: 0.270kg.

The Fameca MTag Voltage Detecor supplied by Hylec are designed for “proving dead”, making sure that nominal voltage is actually absent on a circuit in an HV distribution system between 1 kV and 69 kV. This device will d

The Fameca MTag Voltage Detecor supplied by Hylec are designed for “proving dead”, making sure that nominal voltage is actually absent on a circuit in an HV distribution system between 1 kV and 69 kV. This device will d

C-PROBE LV Ammeter, LV digital w/hookhead. - Allow single operators to measure current on overhead circuits without using platform or ladders. - Soft sensor will avoid stress on LV cable connections - Adapted to night operation: bright yellow

BTC230 TESTER FOR ELECTRICITY METERS. Use: Creates a load at subscriber meter terminals in order to check they are operating correctly. Suited for electromechanical or electronic meters.

Alroc Sheath Stripper 21-35mm, removes the outer sheath.
Circular cutting thickness capacity 2,8mm.
Longitudinal cutting capacity 2,8mm.

RED TRL Blade NOT included

This plier removes the outer sheath with 3 adjustable cutting depths. Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 1.5mm and an interchangeable

This plier removes the outer sheath with 3 adjustable cutting depths. Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 2.0mm and an interchangeable longitudinal TRL cutting cartridge.

This plier removes the outer sheath.
Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 2.8mm and longitudinal cut depth of 3.3mm
For the cables outside diameter ranging between 26

Fameca TAG780 LV Detector with Trigger IPX2x  Heavy duty voltage detector for checking the absence of voltage and giving voltage level indication on low voltage up to 1000V. This device provides additional features as : Display

Penta Pole Insulated Telescopic Stick, 5m Ext. with universal head (1.5m closed length)

• Four fiberglass sections

• Top section of the stick is foam-cored (Proof tested to 100kV per 300mm)

• Approximately 2.

Insulating Glove Class "4" 36kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "4" glove is for electrical work with maximum voltage of 36,000 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&

Insulating Glove Class "3" 26.6kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "3" glove is for electrical work with maximum voltage of 26,600 volts. It is an essential piece of PPE designed to protect workers interacting with expose

Insulating Glove Class 0 1,000V 36cm (14inch) Black IEC 60903

The Regeltex Class "0" glove is for electrical work with maximum voltage of 1,000 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&nbs

Insulating Glove Class "1" 7.5kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "1" glove is for electrical work with maximum voltage of 7,500 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&

Insulating Glove Class "2" 17kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "2" glove is for electrical work with maximum voltage of 17,000 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&

The Arc Flash Gloves, supplied by Hylec are made from Indura Ultra Soft fabric. The highest level of quality and protection in an FR cotton fabric. 88% cotton and 12% high tenacity nylon with guaranteed flame resistance for the life of the garment

Alroc Leadsheath Pliers for cables outside diameter ranging between 26 - 52mm.
Stripping tools designed for circular and longitudinal cutting.
External sheet removal becomes easy with this strong pliers.
Insulated tool. Guaranteed u

This plier removes the outer sheath with 3 adjustable cutting depths. Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 2.0mm and an interchangeable longitudinal TRL cutting cartridge.

Alroc Leadsheath Pliers for cables outside diameter ranging between 46 – 74 mm.
Stripping tools designed for circular and longitudinal cutting.
External sheet removal becomes easy with this strong pliers.
Guaranteed up t

Phase Tester 1000V CatIV-IP65 with interface. PHASE TESTER FOR LV NETWORK 1000V CAT IV - IP65 It is commonly used for detecting stray voltage on poles and cross arms, conductor disconnection on overhead insulated LV conductors…. UNITAG

Penta Pole insulated stick, 9.2m Ext. with universal head (1.7m closed length)
• Seven fiberglass sections
• Top section of the stick is foam-cored
• Approximately 4.7kg in

Penta Pole insulated stick, 9.2m Ext. with universal head (1.7m closed length)
• Eight fiberglass sections
• Top section of the stick is foam-cored
• Approximately 5.5kg in

Penta Pole insulated stick, 12m Ext. with universal head (1.8m closed length)
• Nine fiberglass sections
• Top section of the stick is foam-cored
• Approximately 6.3kg in w

12 cal / cm^{2 ,} Highly Transparent visor, True Colour Vision, allowis user to see red as red, white as white etc. Universal Band to fit on Australian Designed Helmets. Hard coating on outside, anti fog

ALROC stripping Tool - insulation 14-40mm OD.
Medium Voltage Energy cable stripper that enables the user to remove the insulation and set up cutting length.
Insulation thickness capacity: 9mm.
Length 270mm, Width 100mm, Height 165mm

ALROC stripping tool for cable from Ø14 to 40mm.
Removes the bonded semi-conductor from MV and HV cables.
Creates a chamfer on the semi-conductor layer to facilitate the installation of joint, termination or connector.
Adjust

ALROC stripping tool for cable from Ø20 to 50mm.
Removes the bonded semi-conductor from MV and HV cables.
Creates a chamfer on the semi-conductor layer to facilitate the installation of joint, termination or connector.
Adjust

The Alroc CAMF4/40-90-BBCF enables the user:
-To remove the bonded semiconductor
-To remove the Primary/XLPE insulation
Diameter of the cable from 40 to 90 mm.

Alroc MV Bonded Semicon Removal Tool for 18 - 60mm outside diameter. Removes the bonded semi-conducting screen without the need of lubrication in joints, terminations or connectors work. 

MF1+/25 stripping tool for cables from Ø14 to 44mm.
Cable stripper tool removes the bonded semiconductor.
Insulation thickness capacity: 0.4 to 1,4mm.
Length 190mm, Width 85mm, Height 125mm.

ALROC stripping tool for cables from Ø16 to 40mm.
Multifunction cable stripper tool removes outer sheath and insulation.
Insulation thickness capacity: 7mm.
Length 150mm, Width 80mm, Height 100mm.

ALROC stripping tool for cables from Ø16 to 40mm (25 to 240mm²).
Multifunction cable stripper tool removes outer sheath, peelable semi con (red SR stylus included) and insulation.
Insulation thickness capacity: 7mm.
Leng

ALROC stripping tool for cables from Ø16 to 58mm (25 to 630mm²).
Multifunction cable stripper tool removes outer sheath, peelable semi con (red SR stylus included) and insulation.
Insulation thickness capacity: 7mm.
Leng

Download our Electro-PJP catalogue in PDF format.
Find the test and measurement instruments you need for electrical, electronic and electrotechnical applications.
You can take an order in our website or order with the reference number in

ALROC BMFD/50-160 tool to carry out tools stop.
It’s a great tool to prepare the cable ready for joint installation, termination or connector.
Cable diameter from Ø50 to 160mm.
Length 345mm, Width 245mm, Height 50mm.

ALROC CWF3/60 tool removes outer sheath and insulation. 
CWF3/6 is a great tool to prepare the cable ready for joint installation, termination or connector.
Cable diameter from Ø16 to 58mm - Ø0.630-2.2

ALROC BMF-40-90 tool to carry out tools stop. 
It’s a great tool to prepare the cable ready for joint installation, termination or connector. 
Cable diameter from Ø40 to 90mm. 

Insulating half-round bent nose cable cutting pliers with ceramic blades.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V

Insulated Universal Pliers 185mm.
Standards: EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 185mm, Weight 320g

Insulating composite universal pliers with ceramic blades.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 190mm, Weight 110g

Insulating composite universal pliers with ceramic blades.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 200mm, Weight 170g

Fully Insulated Universal Pliers 185mm.
Standards : EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 185mm, Weight 330g

Insulated flat nose pliers 170mm.
Standards: EN 60900 / CIEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 185mm, Weight 185g, Nose length 50mm

Insulated Universal Pliers 220mm.
Standards: EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 220mm, Weight 450g

Insulated wire stripper 175mm.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 175mm, Weight 260g

Insulating Glove Class "2" 17,000kV 41cm (16 inch) Beige. IEC 60903

The Regeltex Class "2" glove is for electrical work with maximum voltage of 17,000 volts. It is an essential piece of PPE designed to protect workers interacting with expo

Insulating Glove Class 00 500V 36cm (14inch) Black IEC 60903

The Regeltex Class "00" glove is for electrical work with maximum voltage of 500 volts. It is an essential piece of PPE designed to protect workers interacting with exposed 

A/F 12.4 cal Suit Kit c/w Std Hood XL

• Stanco Arc Flash ( PPE ) Protective Switching Suit - Clothing Kit. Conforming to Standard: NFPA 70E HRC/CAT 4 ASTM D6413. Available Standard Cal ratings: 8, 12, 21, 25, 40, 44, 57 & 74cal.

Alroc XLPE enables a chamfer of 30 mm at the extremity of the insulation of MV cables. For 14-40mm cable diameter.

Alroc LH2 cable tools used by MV-HV jointers to remove the insulation to prepare the cable ready for the installation of joints, terminations or connectors. 
Maximum cutting depth: 17mm.
Length 425mm, Width 105mm, Height 85mm.<

The gold SRC stylus can remove the peelable semi-conductor without touching the primary insulation located underneath.
4 scoring depths: 0.4mm / 0.7mm / 0.9mm / 1.1mm.
Diameter: ø14 - 58 mm.
Must be used with the following to

Alroc LH3 cable tools used by MV-HV jointers to remove the insulation.
Prepare the cable ready for the installation of joints, terminations or connectors.
Maximum cutting depth: 24mm.
Cable diameter from 60 to 80mm.
Length 460m

The silver SRC-D stylus can remove the peelable semi-conductor without touching the primary insulation located underneath.
4 scoring depths: 0.4mm / 0.7mm / 0.9mm / 1.1mm.
Diameter: ø16 - 58 mm.
Must be used with the followin

Alroc LH4 cable tools used by MV-HV jointers to remove the insulation.
Prepare the cable ready for the installation of joints, terminations or connectors.
Maximum cutting depth: 29mm
Cable diameter from 80 to 110mm.
Length 640m

The green SCH stylus can make a chamfer on the extremity of the primary insulation.
Diameter: ø16 - 60 mm.
Must be used with the following tools: MF1+/25, MF1+/60, MF3/40, MF3/60, MF3/40-SR, MF3/60-SR, MF3/40-C, MF3/60-C

Insulating composite cable cutting pliers.
Standards: EN 60900 / IEC 60900.
Guaranteed up to 1000V.
Length 190mm, Weight 165g
Apllication range: Opening 22mm, Aluminium 35mm² Copper 16mm²

INSULATED RATCHET CABLE CUTTER Ø 25 MM WITH INSULATING HEAD COVER 290MM L ALUM 300MMSQ & COPPER 240MMSQ - EN 60900 / IEC 60900.  this tool can be used with a wedge with groove 5544E.

Insulated Pliers Side Cutter 190mm.
Standards : EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 190mm, Weight 370g

Insulated ratchet cable cutter 32mmOD.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 260mm, Weight 740g
Application range: Opening 32mm, Aluminium 300mm² Copper 340mm²

Insulated Pliers Cutter 230mm.
Standards : EN 60900 / IEC 60900
Guaranteed up to 1000V
Opening 24mm, Length 230mm, Weight 500g

Multi range testing clamp is used to connect a sensing device or voltage meter to an insulated conductor by puncturing the conductor insulation without the need of stripping.

Road Shell Cable Cover - suits Warm Climate Low Profile 120mm. Two channels 92mm & four channels 40mm

The Alroc EVP enables the user to flare and spread the lead sheath or the tabs made from the lead sheath. Spread without damaging underlying layers.

ALROC stripping Tool. 6 sections from 16 to 150mm².
Low voltage cable stripper 6 sections. For overhead cable. Enables the user to remove the insulation.
Sections : 16 - 25 - 35 - 54,6 - 70 - 150m²
Length 130mm, Width 130m

The DSP tool remove and catch the peelable semiconductor at the end of cable.
Diameter: ø10 - 80 mm.
Can be used with the following tools: MF1+/25, SR, SRC, MF1+/60, SRC-D, MF3/40, MF3/60.

The MV Bonded semicon is a very reliable product, well designed using high quality steel and aluminium. This tool is targeted to get a very long-life duration.

Gripall Stick 1.22m/4ft OAL Orange. To suit shotgun ring / gripper spindles. This gripall / shotgun hot stick is an essential piece of Insulating equipment to protect technicians when working with high voltage machines and conductors, where a

Regeltex RGX-1704 is a quick drying professional rubber cleaner in a ready to use 200ml spray bottle.RGX is specifically developed to properly clean rubber insulating materials such as gloves and mats. For best results we recommend to us

The BGT Sibille Safe Glove box has been designed for the safe storage and protection of electrical gloves. This unit is portable with folding handle, it can also be wall mounted for use in electrical substations, technical rooms etc. 

TESTER FOR INSULATING GLOVES

Use: The purpose of the tester is to ensure that the glove is absolutely air-tight.

Hylec glove bag is made from heavy duty canvas material. This will suit to store all classes of insulating gloves and leather over gloves with 41cm (16 inch) length from class 00 to 4.

9.4 cal  HRC2  Kevlar Glove - Cut and Fire Resistant (FR)  Size 10

See below for product detail >>

Individual electric field detection with headlamp.
For MV Overhead lines 10 000 to 69 000V, work from elevated platforms only.
Provide extra safety level for workers operating near energized equipment.
Dimensions: 87x60x34mm.
W

This triple pocket glove bag supplied by Hylec is made from a canvas material. This will suit all classes of insulating gloves with two (2) extra pockets to fit all your insulating glove accessories.

Hylec glove bag is made from PVC material. This will suit to store all classes of insulating glove and leather over glove with 36cm (14 inch) length from Class 00 to 4.

FAMECA Bipolar voltage detector. Composed with a probe and a pole that allows the detection of DC voltages as well as AC.
Rated voltage: 400V to 3600V.
Meta case size: 450x345x127mm
Weight: 1.75kg.

Hylec glove bag is made from PVC material. This will suit to store all classes of insulating glove and leather over glove with 41cm (16 inch) length from Class 00 to 4.