This plier removes the outer sheath with 3 adjustable cutting depths.
Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 1mm and an interchangeable longitudinal cutting cartridge. (not

4 Nm TORQUE LIMITING SCREWDRIVER

For controlled tightening to 4 Nm of electrical meter or circuit breaker terminal blocks. When 4 Nm torque is reached, the torque device trips to allow optimum tightening, and tightening above 4 Nm is impos

Insulated hacksaw. A product designed to do a safe work in LV live working.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 450mm, Weight 740g, Blade length 300mm

Insulated junior hacksaw. Used for a more precise cutting, confined area cutting or application that requires a neater finish.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 263mm, Weight 150g, Blade length 130mm

C-PROBE LV Ammeter, LV digital w/hookhead. - Allow single operators to measure current on overhead circuits without using platform or ladders. - Soft sensor will avoid stress on LV cable connections - Adapted to night operation: bright yellow

Testing and measuring the continuity of protective conductors and equipotential bonding.
Double-sleeved 1mm² PVC cable measurements.
Reverses automatically the polarities
CAT III-600V and CAT IV 300V safety rating.
Measure

BTC230 TESTER FOR ELECTRICITY METERS. Use: Creates a load at subscriber meter terminals in order to check they are operating correctly. Suited for electromechanical or electronic meters.

FAMECA voltage detector with integrated self-test. Compact optical and acoustic detector with LEDs.
Rated voltage: 127V to 90 000V.
Frequency: 50 and 60Hz.
Length: 195mm, Diameter: 49mm
Weight: 0.270kg.

The TT7R2LW is a mobile device designed for field testing, allowing to inspect the electric insulation’s defects or cleanliness on equipment before using, or within the preliminary frame of the periodical and in

The Fameca MTag Voltage Detecor supplied by Hylec are designed for “proving dead”, making sure that nominal voltage is actually absent on a circuit in an HV distribution system between 1 kV and 69 kV. This device will d

The Fameca MTag Voltage Detecor supplied by Hylec are designed for “proving dead”, making sure that nominal voltage is actually absent on a circuit in an HV distribution system between 1 kV and 69 kV. This device will d

PINTEL 4 BT Cable Stripper pliers.
Enables to make circular and longitudinal cut, including LV/MV cylindrical or sectoral conductor, in order to remove cable’s outer jacket.
For cable from 9 mm to 30 mm.
Circular cutting: 3.3

Alroc Sheath Stripper 21-35mm, removes the outer sheath.
Circular cutting thickness capacity 2,8mm.
Longitudinal cutting capacity 2,8mm.

Electrically Insulating Helmet with Integrated Face Shield.

Highest protection against arc flash, class 2 according to BOX TEST,

RED TRL Blade NOT included

This plier removes the outer sheath with 3 adjustable cutting depths. Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 1.5mm and an interchangeable

This plier removes the outer sheath with 3 adjustable cutting depths. Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 2.0mm and an interchangeable longitudinal TRL cutting cartridge.

Fameca TAG780 LV Detector with Trigger IPX2x  Heavy duty voltage detector for checking the absence of voltage and giving voltage level indication on low voltage up to 1000V. This device provides additional features as : Display

Penta Pole Insulated Telescopic Stick, 5m Ext. with universal head (1.5m closed length)

• Four fiberglass sections

• Top section of the stick is foam-cored (Proof tested to 100kV per 300mm)

• Approximately 2.

This plier removes the outer sheath.
Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 2.8mm and longitudinal cut depth of 3.3mm
For the cables outside diameter ranging between 26

Insulating Glove Class "4" 36kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "4" glove is for electrical work with maximum voltage of 36,000 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&

Insulating Glove Class 0 1,000V 36cm (14inch) Black IEC 60903

The Regeltex Class "0" glove is for electrical work with maximum voltage of 1,000 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&nbs

Insulating Glove Class "1" 7.5kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "1" glove is for electrical work with maximum voltage of 7,500 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&

Insulating Glove Class "2" 17kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "2" glove is for electrical work with maximum voltage of 17,000 volts. It is an essential piece of PPE designed to protect workers interacting with exposed&

Insulating Glove Class "3" 26.6kV 41cm (16 inch) Black. IEC 60903

The Regeltex Class "3" glove is for electrical work with maximum voltage of 26,600 volts. It is an essential piece of PPE designed to protect workers interacting with expose

The Arc Flash Gloves, supplied by Hylec are made from Indura Ultra Soft fabric. The highest level of quality and protection in an FR cotton fabric. 88% cotton and 12% high tenacity nylon with guaranteed flame resistance for the life of the garment

Composite Insulating gloves with ARC Flash protection. Standards IEC 60903, 61482-1-2, ASTM F2675

The Class 0 composite glove is for electrical work with maximum voltage of 1,000 volts. It is an essential piece of PPE designed to protect w

Alroc Leadsheath Pliers for cables outside diameter ranging between 26 - 52mm.
Stripping tools designed for circular and longitudinal cutting.
External sheet removal becomes easy with this strong pliers.
Insulated tool. Guaranteed u

This plier removes the outer sheath with 3 adjustable cutting depths. Stripping tools designed for circular and longitudinal cutting.
This model has a circular cut depth of 2.0mm and an interchangeable longitudinal TRL cutting cartridge.

Alroc Leadsheath Pliers for cables outside diameter ranging between 46 – 74 mm.
Stripping tools designed for circular and longitudinal cutting.
External sheet removal becomes easy with this strong pliers.
Guaranteed up t

Phase Tester 1000V CatIV-IP65 with interface. PHASE TESTER FOR LV NETWORK 1000V CAT IV - IP65 It is commonly used for detecting stray voltage on poles and cross arms, conductor disconnection on overhead insulated LV conductors…. UNITAG

Penta Pole insulated stick, 9.2m Ext. with universal head (1.7m closed length)
• Seven fiberglass sections
• Top section of the stick is foam-cored
• Approximately 4.7kg in

Penta Pole insulated stick, 9.2m Ext. with universal head (1.7m closed length)
• Eight fiberglass sections
• Top section of the stick is foam-cored
• Approximately 5.5kg in

Hand Held Remote Electrical Field Detector with direction Barrell detects live conducts at ground level HV Remote Electrical Field Detector. The DCEDB382 remotely detects the presence of electrical fields from the pylon or even from the groun

Penta Pole insulated stick, 12m Ext. with universal head (1.8m closed length)
• Nine fiberglass sections
• Top section of the stick is foam-cored
• Approximately 6.3kg in w

TransVision Shield^™  Next-generation arc flash protection.

Clear Vision - Darkens instantly to protect your eyes

12 cal / cm^{2 ,} Highly Transparent visor, True Colour Vision, allowis user to see red as red, white as white etc. Universal Band to fit on Australian Designed Helmets. Hard coating on outside, anti fog

The Modiewark is a Non-Contact & Contact Voltage Detector Proximity and Touch device that detects the presence of an alternating electric field.

Its uniqu

FAMECA's operating insulating stick 1.5m length supplied by Hylec are made from high quality foam-cored tubes that can be used on high voltage applications. With a universal (sunrise) end fitting, you can easily attach different adaptors to apply

FAMECA's operating insulating stick 1.0m length supplied by Hylec are made from high quality foam-cored tubes that can be used on high voltage applications. With a universal (sunrise) end fitting, you can easily attach different adaptors to apply

FAMECA's operating insulating stick 1.8m length supplied by Hylec are made from high quality foam-cored tubes that can be used on high voltage applications. With a universal (sunrise) end fitting, you can easily attach different adaptors to apply

Download our Electro-PJP catalogue in PDF format.
Find the test and measurement instruments you need for electrical, electronic and electrotechnical applications.
You can take an order in our website or order with the reference number in

ALROC stripping tool for cable from Ø14 to 40mm.
Removes the bonded semi-conductor from MV and HV cables.
Creates a chamfer on the semi-conductor layer to facilitate the installation of joint, termination or connector.
Adjust

ALROC stripping tool for cable from Ø20 to 50mm.
Removes the bonded semi-conductor from MV and HV cables.
Creates a chamfer on the semi-conductor layer to facilitate the installation of joint, termination or connector.
Adjust

The Alroc CAMF4/40-90-BBCF enables the user:
-To remove the bonded semiconductor
-To remove the Primary/XLPE insulation
Diameter of the cable from 40 to 90 mm.

Alroc MV Bonded Semicon Removal Tool for 18 - 60mm outside diameter. Removes the bonded semi-conducting screen without the need of lubrication in joints, terminations or connectors work. 

MF1+/25 stripping tool for cables from Ø14 to 44mm.
Cable stripper tool removes the bonded semiconductor.
Insulation thickness capacity: 0.4 to 1,4mm.
Length 190mm, Width 85mm, Height 125mm.

ALROC stripping tool for cables from Ø16 to 40mm.
Multifunction cable stripper tool removes outer sheath and insulation.
Insulation thickness capacity: 7mm.
Length 150mm, Width 80mm, Height 100mm.

ALROC stripping tool for cables from Ø16 to 40mm (25 to 240mm²).
Multifunction cable stripper tool removes outer sheath, peelable semi con (red SR stylus included) and insulation.
Insulation thickness capacity: 7mm.
Leng

ALROC stripping tool for cables from Ø16 to 58mm (25 to 630mm²).
Multifunction cable stripper tool removes outer sheath, peelable semi con (red SR stylus included) and insulation.
Insulation thickness capacity: 7mm.
Leng

ALROC BMFD/50-160 tool to carry out tools stop.
It’s a great tool to prepare the cable ready for joint installation, termination or connector.
Cable diameter from Ø50 to 160mm.
Length 345mm, Width 245mm, Height 50mm.

Insulated flat nose pliers 170mm.
Standards: EN 60900 / CIEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 185mm, Weight 185g, Nose length 50mm

ALROC BMF-40-90 tool to carry out tools stop. 
It’s a great tool to prepare the cable ready for joint installation, termination or connector. 
Cable diameter from Ø40 to 90mm. 

Insulated wire stripper 175mm.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 175mm, Weight 260g

ALROC stripping Tool - insulation 14-40mm OD.
Medium Voltage Energy cable stripper that enables the user to remove the insulation and set up cutting length.
Insulation thickness capacity: 9mm.
Length 270mm, Width 100mm, Height 165mm

Insulating half-round bent nose cable cutting pliers with ceramic blades.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V

Insulated Universal Pliers 185mm.
Standards: EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 185mm, Weight 320g

Insulating composite universal pliers with ceramic blades.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 190mm, Weight 110g

Insulating composite universal pliers with ceramic blades.
Standards: EN 60900 / IEC 60900
Guaranteed up to 1000V
Length 200mm, Weight 170g

Fully Insulated Universal Pliers 185mm.
Standards : EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 185mm, Weight 330g

ALROC CWF3/60 tool removes outer sheath and insulation. 
CWF3/6 is a great tool to prepare the cable ready for joint installation, termination or connector.
Cable diameter from Ø16 to 58mm - Ø0.630-2.2

Insulated Universal Pliers 220mm.
Standards: EN 60900 / IEC 60900 / ISO 5743 / ISO 5744 / ISO 5749
Guaranteed up to 1000V
Length 220mm, Weight 450g

Hylec's operating insulating stick 1.5m screw type are made from high quality foam-cored tubes that can be used on high voltage applications. With a universal (sunrise) end fitting, you can easily attach different adaptors to apply i.e. Earthing,

Insulating Glove Class "2" 17,000kV 41cm (16 inch) Beige. IEC 60903

The Regeltex Class "2" glove is for electrical work with maximum voltage of 17,000 volts. It is an essential piece of PPE designed to protect workers interacting with expo

Insulating Glove Class 00 500V 36cm (14inch) Black IEC 60903

The Regeltex Class "00" glove is for electrical work with maximum voltage of 500 volts. It is an essential piece of PPE designed to protect workers interacting with exposed 

Composite Insulating gloves with ARC Flash protection. Standards IEC 60903, 61482-1-2, ASTM F2675

The Regeltex Class 2 composite glove is for electrical work with maximum voltage of 17,000 volts. It is an essential pi

Composite Insulating Gloves with ARC Flash protection. Standards IEC 60903, 61482-1-2, ASTM F2675

The Class 3 composite glove is for electrical work with maximum voltage of 26,600 volts. It is an essential piece of PPE designed to protect

Stanco HRC2 Arc Flash 12.4 cal Kit 2. Contents: Knee Length 50" Coat, GCA Class 0 Electrical Mechanical Arc Flash Gloves, Standard Hood, Australian Designed Standard helmet (for under hood use) , 15" Leggings, GB50 Deluxe

A/F 12.4 cal Suit Kit c/w Std Hood XL

• Stanco Arc Flash ( PPE ) Protective Switching Suit - Clothing Kit. Conforming to Standard: NFPA 70E HRC/CAT 4 ASTM D6413. Available Standard Cal ratings: 8, 12, 21, 25, 40, 44, 57 & 74cal.

Multi range testing clamp is used to connect a sensing device or voltage meter to an insulated conductor by puncturing the conductor insulation without the need of stripping.

Alroc XLPE enables a chamfer of 30 mm at the extremity of the insulation of MV cables. For 14-40mm cable diameter.